Aluminum Electrolytic Capacitor CapXon DV221M025E077ETR 220 Microfarad 25 Volt for Temperature Range

Product Overview

The CapXon DV series Aluminum Electrolytic Capacitors are designed for general-purpose applications, offering reliable performance and durability. These capacitors are suitable for a wide operating temperature range of -55 to 105C and are built to meet stringent quality standards, including JIS-C-5101-1. They are manufactured by CapXon Electronic (Shenzhen) Co., Ltd., a company committed to environmental compliance and adherence to RoHS regulations.

Product Attributes

• Brand: CapXon
• Series: DV
• Origin: Shenzhen, China
• Environmental Policy: Compliant with Montreal Protocol (no ozone-depleting chemicals used), adheres to RoHS regulations.
• Quality Standards: Meets or exceeds JIS-C-5101-1 and JIS-C-5101-4/-18 reliability requirements.

Technical Specifications

Model: DV221M025E077ETR

Important Notes and Characteristics

General Information:

• Maximum RMS Ripple Current: Specified at +105C, 100KHz. Adjustments for different temperatures and frequencies are necessary using provided coefficients. Verification methods follow JIS-C-5101-1(2010) No.: 4.23. Self-generated heat should be within 5C if ripple current is difficult to measure.
• Working Voltage: Ensure applied voltage does not exceed the rated voltage. Peak voltage (DC + ripple) must not exceed the rated voltage.
• Insulation: Standard capacitors have a vinyl sleeve for marking. For insulated aluminum cases, special types are recommended.
• Soldering: Avoid excessive soldering temperature or time to prevent sleeve shrinkage. Solder on the reverse of the PC board. Maintain a distance between the capacitor and the circuit board to prevent sleeve damage.
• Vent: Capacitors (10mm) have a safety vent at the bottom to release internal pressure during unsafe usage.
• High Altitude: Capacitors can withstand transportation at -55~105C and altitudes up to 20,000 feet.
• Cleaning Agents: Avoid halogenated organic solvents, as they may penetrate and cause corrosion.

Technical Performance Testing Environment:

• Temperature: 1535C (Standard), 2510C (Judgment), 201C (Dispute)
• Humidity: 2575%RH (Standard), 4060%RH (Judgment), 6367%RH (Dispute)
• Air Pressure: 86KPa106KPa

Key Test Items and Criteria:

• Capacitance Measurement: 202C, 120Hz, 0.5Vrms. Tolerance: -20~20%.
• Dissipation Factor (tan) Measurement: 202C, 120Hz, 0.5Vrms. Refer to Table 1 for criteria.
• Leakage Current Measurement: Rated voltage applied for 2 minutes with a 100010% protection resistor. Criterion: I 55A.
• Terminal Strength: Tested for tensile and bending strength with specified loads and cycles. Terminals must not be loose, broken, or have poor contact.
• Temperature Characteristic: Impedance measured at different temperatures. Impedance ratio must not exceed values in Table 2. Leakage current (LC) 800% of initial specification.
• High Temperature Load (2000H/105C): Capacitance change 30%, DF 300% of spec, LC spec, no visible damage.
• High Temperature Exposure (Storage, 1000H/105C): Capacitance change 30%, DF 300% of spec, LC spec, no visible damage.
• Surge Test (1000 cycles): Applied voltage 29V. Capacitance change 15%, DF spec, LC spec, no visible damage.
• Vibration Test: 10~55Hz, 0.75mm amplitude, 98 m/s acceleration for 6 hours (X, Y, Z directions). Capacitance change 5%, DF spec, LC spec, no visible damage.
• Solderability: Sn96.5%Ag3%Cu0.5% solder at 2455C for 2.00.5S. New solder coverage > 95%.
• Resistance to Soldering Heat: Specific profiles for different sizes (T1, t1, Peak temp). Reflow acceptable twice.
• Vent Test (for applicable products): Reverse voltage 80V. No explosion, flash, flame, spark, or fire when vent operates.
• Temperature Cycling (10 cycles): Capacitance change 5%, DF spec, LC spec, no visible damage.
• High Temp and Humidity (250H/40C/90~95%RH): Capacitance change 20%, DF 1.2 times spec, LC spec, no visible damage.

Marking Example:

220 25V DV 08 D

• (1) 25V: Rated Voltage
• (2) 220: Nominal Capacitance (F)
• (3) Shadow part: Polarity (Cathode Indicate)
• (4) DV: Series Mark
• (5) 08: Date Code (Year: last digit, Month: 1-9, A=10, B=11, C=12)

Characteristics Tables:

• Table 1: Dissipation Factor (DF) max (%) - Values provided for various working voltages (6.3V to 100V).
• Table 2: Impedance Ratio (Z-25Z+20, Z-40Z+20) max - Values provided for various rated voltages.
• Table 3: Multiplier for Ripple Current vs. Frequency - Coefficients for adjusting ripple current based on frequency and capacitance.

General Disclaimers:

• Specifications are subject to change without notice.
• Operating conditions affect lifetime; consult Capxon for calculations.
• For aerospace, military, life-saving, or life-sustaining applications, consult Capxon before design-in.
• Buyer is responsible for ensuring product suitability for their application.
• Capxon provides express warranties only and disclaims all other warranties.
• Further information is available at www.capxongroup.com.

Aluminum Electrolytic Capacitor CapXon DV221M025E077ETR 220 Microfarad 25 Volt for Temperature Range Images